Skip to content

Strategy 2: Iterative Optimization

In the V3 review

Literature scenarios that tune parameters across trials (Fig. 3):

  • dispense → weigh → optimize: Bayesian optimization of aspirate/dispense parameters under gravimetric feedback, <5% error at 1275 cP on an Opentrons OT-2 [11].
  • draw → tune → dose: vacuum flow and orifice size tuned for ≤0.1% RSD milligram powder transfers (one powder, offline) [37].
  • pour → mix → assess: Bayesian optimization with computer-vision foam assessment to reconstitute a powdered beverage [42].

Bayesian optimization [135] and libraries such as BoTorch [136] make this routine; see Data & Decision Models.

Overview

Dispense, measure, adjust, repeat until target is met.

This strategy treats material handling as an optimization problem: perform a trial dispensing, measure the outcome, adjust parameters based on the measurement, and repeat until accuracy requirements are met.


When to Use

  • High accuracy required (±0.5% or better)
  • Model is uncertain (don't trust first-principles calculations)
  • Material variation is high between batches or within a batch
  • Feedback sensors available (balance, fill-height camera, pressure transducer)
  • Computational resources are modest (linear model, not deep learning)
  • Time budget allows for multiple dispense cycles (3–10 iterations typical)

How It Works

Step 1: Initial Guess

Start with a nominal parameter set: - From a prior model (Strategy 1) - From literature or manufacturer data - From past similar material

Example: Dispense first 5 g of powder at speed = 50 rpm (nominal).

Step 2: Measure Outcome

After each dispensing, measure what was actually delivered:

  • Gravimetric: Place collection vessel on balance, measure mass
  • Volumetric: Use graduated cylinder or measure volume change
  • Fill height: Use camera to estimate volume from fill height in container
  • Pressure/flow: Monitor pressure drop or flow rate during extrusion

Accuracy: Measurement must be at least 5× more accurate than your final tolerance. (For ±1% target, measure to ±0.2%.)

Step 3: Compute New Parameters

Use the error to estimate a better parameter set:

Linear Model (Most Common)

If outcome is linear in the parameter:

\[ \text{outcome} = \text{baseline} + \text{sensitivity} \times (\text{parameter} - \text{nominal}) \]

Example:

  • Trial 1: dispense at speed S₁ = 50 rpm → measure M₁ = 4.8 g
  • Target: 5.0 g
  • Error: ΔM = 5.0 − 4.8 = 0.2 g (too low)
  • Sensitivity: Assume ΔM / ΔS ≈ 0.1 g/rpm
  • New speed: S₂ = S₁ + ΔM / sensitivity = 50 + 0.2 / 0.1 = 52 rpm

Quadratic or Non-Linear Model

For non-linear systems, use: - Polynomial fit if you have 3+ data points - Gaussian process regression if you have time and want confidence intervals - Neural network if you have 20+ historical examples

Step 4: Repeat Until Converged

Dispense again at S₂, measure M₂, adjust to S₃, etc.

Convergence criterion: When |M_{n+1} − target| < tolerance, stop.

Typical trajectory:

Trial 1: M = 4.8 g (1.8 mg short)    → update model
Trial 2: M = 5.05 g (0.5 mg over)    → refine
Trial 3: M = 4.99 g (0.1 mg short)   → PASS

Advantages

Aspect Benefit
Accuracy Can achieve ±0.5–1% accuracy even with unknown material
Robustness Automatically corrects for drift, temperature, batch variation
Model-free No need to measure physical properties or fit a complex model
Adaptive Learns the relationship on the fly for each material
Failure recovery If first trial is wrong, subsequent trials correct it

Limitations

Challenge Issue
Time Takes 3–10 dispense-measure cycles (10–30 minutes typical)
Waste Each trial uses material; can add up for expensive substances
Non-linearity If relationship is highly non-linear, may not converge or overshoot
Measurement noise If balance is noisy (±0.05 g), errors propagate
Parameter constraints May try to set pump speed or pressure outside hardware limits

Real-World Examples

Example 1: Powder Dispensing by Weight

Task: Dispense 1.0 g of API (Active Pharmaceutical Ingredient) powder, 20 times

Procedure:

  1. Set auger feeder to nominal 30 rpm
  2. Dispense trial 1 → weigh → 0.95 g (50 mg short)
  3. Model: ΔM = 1.7 mg/rpm
  4. Update: speed₂ = 30 + 50/1.7 ≈ 30 rpm (negligible change, but be patient)
  5. Dispense trial 2 → 1.01 g (PASS)
  6. Dispense 20 final doses at 30 rpm
  7. Each dose: 1.0 ± 0.02 g

Time: ~5 minutes for calibration + 5 minutes for 20 doses.

Alternative (faster): Dispense 3–5 trials to map the sensitivity curve, then all 20 final doses at optimized speed.


Example 2: Liquid Volume in Syringe Extrusion

Task: Extrude 1.0 mL of silicone polymer ink onto a 3D printing substrate

Procedure:

  1. Set motor speed to 10 mm/s plunger speed
  2. Dispense trial 1 → measure bead volume (via image analysis) → 0.92 mL (80 µL short)
  3. Sensitivity: 8 µL/mm/s
  4. Speed₂ = 10 + 80/8 = 20 mm/s (Too aggressive? Try 15 mm/s for safety)
  5. Dispense trial 2 at 15 mm/s → 1.03 mL (PASS, or close)
  6. Adjust to 14.5 mm/s if needed
  7. Dispense 5 final beads at 14.5 mm/s
  8. Each bead: 1.0 ± 0.05 mL

Measurement: Use calibrated syringe or optical measurement.


Example 3: Paste Extrusion with Pressure Control

Task: Extrude 2 mL of ink at consistent flow rate

Procedure:

  1. Air-pressure syringe set to 200 kPa nominal
  2. Trigger extrusion, measure extrusion time for 2 mL → 4.5 seconds (faster than expected)
  3. Flow rate: 2 mL / 4.5 s = 0.44 mL/s
  4. Target flow rate: 0.4 mL/s (slower, for precision)
  5. Pressure sensitivity: 0.05 mL/s per 10 kPa
  6. Required pressure: 200 − 10×0.04/0.05 ≈ 192 kPa
  7. Adjust to 190 kPa and retry
  8. Measure extrusion time → 5.0 seconds (0.40 mL/s) ✓ PASS

Linear Calibration Model (Most Practical)

For most dosing tasks, a linear 1-parameter model suffices:

\[ \text{dose} = \alpha + \beta \times \text{control\_parameter} \]

Calibration Procedure

  1. Collect 3 data points at different settings:
  2. Setting A: dose_A
  3. Setting B: dose_B
  4. Setting C: dose_C
  5. Fit the line: $$ \beta = \frac{(\text{dose}_B - \text{dose}_A)}{(\text{setting}_B - \text{setting}_A)} $$ $$ \alpha = \text{dose}_A - \beta \times \text{setting}_A $$
  6. Predict setting for target dose: $$ \text{setting} = \frac{\text{target_dose} - \alpha}{\beta} $$
  7. Execute at predicted setting.
  8. (Optional) Fine-tune: If measured dose differs from target by > 2%, adjust once more.

Example Calibration Table for Powder Auger

Auger Speed (rpm) Measured Dose (g)
40 0.90
50 1.10
60 1.30

Fit: slope β = (1.30 − 0.90) / (60 − 40) = 0.02 g/rpm, intercept α = 0.90 − 0.02×40 = 0.10 g

Target: 1.00 g → setting = (1.00 − 0.10) / 0.02 = 45 rpm

Verify: At 45 rpm, expect (0.10 + 0.02×45) = 1.00 g ✓


Implementation Checklist

  • Define target dose and tolerance (e.g., 5.0 ± 0.1 g)
  • Choose measurement device (balance, camera, flow meter) and verify accuracy
  • Start with nominal parameter (literature, prior data, or guess)
  • Dispense trial 1, measure outcome
  • If within tolerance, proceed to main task; if not, continue
  • Fit linear model (or use proportional control if only one trial)
  • Predict next parameter value
  • Dispense trial 2, measure
  • Repeat until within tolerance (typically 2–4 iterations)
  • Document calibration for future reference
  • Dispense all final doses at optimized parameter
  • Verify final doses meet specification

Comparison with Other Strategies

Strategy Time to Deploy Accuracy Robustness Sensor Requirement
Characterize, then act Very fast (1 min) ±5% Low Minimal
Iterative optimization Medium (10–20 min) ±1% High Balance, scale
Real-time correction Medium (5–10 min) ±1–2% Very high Fast sensor
Feedforward prediction Very fast (1 min) ±2% Medium Rheometer, model

References

  • Rastegardoost, M. M.; Bao, Z.; Sadr, S.; Abdollahi, N.; Darvish, K.; Clasky, A.; Ohsaka, H.; Le Devedec, F. Self-Driving Laboratories for Formulation: Handling Liquids, Pastes, Powders and Objects, from Robots to Digital Twins and AI Agents. Manuscript in preparation, 2026.
  • Key references from the review: [11], [37], [42], [135], [136]. Full list on the References page.

Further reading (from the earlier wiki)

  • Hastie, T., Tibshirani, R., & Friedman, J. (2009). The Elements of Statistical Learning. Springer.
  • Box, G. E., Hunter, W. G., & Hunter, J. S. (1978). Statistics for Experimenters. Wiley.