Skip to content

Retrofits Beyond Factory Specification

Step 4 · Extend: How to go beyond the catalog?

Summarizes Section 5 (Customizing Platforms Beyond Their Factory Specification) and Table 5 of the review.

The optional gripper arms on the Opentrons Flex and the Hamilton Microlab STAR are the manufacturer-approved route to generalization. A larger body of work gets there without the vendor. Researchers keep a platform's gantry, deck and control loop, then swap its end-effector, add a sensor or replace its control software to unlock a capability the manufacturer never sold.

The literature scenarios ask how a material should be handled. This work asks a different question: which layer of a platform you already own should you modify (mechanical, sensing or software) so that one machine can cover more steps of a formulation workflow? Table 5 groups ten studies by that layer. Three of them also appear among the liquid-handling scenarios; seven are new here.

Table 5: Retrofits that extend platforms beyond their factory specification

Layer modified Base platform Novel idea New capability unlocked Ref
Control parameters (unmodified hardware) Opentrons OT-2 Bayesian-optimize aspirate/dispense speed against gravimetric feedback instead of a fixed viscosity lookup table <5% error dispensing liquids up to 1275 cP on a robot rated for water-like liquids [11]
Opentrons OT-2 Treat the pipetting robot’s own dispense-time/mass data as a viscosity-proxy signal Turns a liquid handler into a high-throughput viscometer with no dedicated rheometer [23], [81]
End-effector replacement Generic robot arm Replace the pipette tip with a vibrating acoustofluidic coupler Mixes liquids ~10⁶× more viscous than water without a pump [25]
Opentrons OT-1 3D-printed adapter turns the robot’s own stepper motor into an infuse/withdraw syringe pump Extends a microliter-rated robot to 15–50 nL transfers for under $6,000 total system cost [82]
Councill’s modified Opentrons OT-1 Add two-position/selector valves to the same syringe-pump retrofit Same platform doubles as an autosampler feeding an LC-MS instrument [83]
Generic robot arms Sub-$200, three-part 3D-printed pipette end-effector Lets arms that cannot grip a pipette at all reach commercial-liquid-handler accuracy [84]
Generic tool-exchange gripper Container-shape taxonomy drives dual-material compliant gripper-finger design One gripper reliably grasps vessel shapes a stock gripper’s fingers cannot [85]
Sensing add-on via tool-changing Opentrons OT-2 Adapter with two mounting bores lets the existing tool-change slot carry a pipette or a camera Same robot alternates dispensing and in-situ imaging without a separate imaging station [86]
Opentrons OT-2 Mount a camera + transilluminator, pair with a Detectron2 vision model Liquid handler gains automated colony picking (~240/h) at a fraction of a dedicated picker’s cost [87]
Software/control layer Opentrons, Hamilton, Tecan Hardware-agnostic Python driver replaces vendor firmware Exposes physically possible moves vendor software never programmed, e.g., dual-plate pipetting [88]

Three families of retrofit

1. Replace the end-effector

The most direct retrofit keeps the motion system and replaces the end-effector (Table 5, rows 3–7). There are two threads.

Reuse the robot's own actuator. Councill et al. turn the stepper motor of the now-discontinued Opentrons OT-1 into a nanoliter syringe pump [82]. Axtell et al. show that the same retrofit, with valves added, also works as an LC-MS autosampler [83].

Platform-agnostic tools. Yoshikawa et al.'s open-hardware digital pipette [84] and Zwirnmann et al.'s gripper fingers, designed from a container-shape taxonomy [85], fit any compatible arm. They give up deep integration in exchange for reuse across a fleet.

2. Use the tool changer as a sensor mount

A second family uses the tool-change mechanism, built for pipette tips, to mount a different tool. Nazeri et al. [86] and del Olmo Lianes et al. [87] both mount a camera on an Opentrons OT-2: the first to monitor dispensing, the second to pick colonies. What is new is not the commodity camera but the idea of treating a consumables interface as a general-purpose mount.

3. Replace the control software

A third family works at the software layer. Wierenga et al.'s PyLabRobot [88] replaces proprietary control software with one hardware-agnostic Python interface for Opentrons, Hamilton and Tecan platforms. It exposes moves that are physically possible but that vendor firmware never programmed, such as an 8-channel head servicing two microplates in one motion.

Layers like this underpin every other customization. A robot cannot act on a new sensor through firmware that refuses non-standard commands, and a formulation workflow cannot be orchestrated across instruments that refuse a common interface. See also Orchestration.

Why it matters

Together, these retrofits can turn a $15,000–30,000 liquid handler into a nanoliter dispenser, an autosampler, a colony picker or an imaging station. The cost is a few hundred dollars in printed parts plus a workaround in the control layer. They are a lower-cost counterpart to the new-hardware scenarios E–H in Figure 3, and they turn single-purpose robots into the multi-function platforms formulation SDLs need.

Every new capability is a new failure mode

Proving a retrofit on the physical cell is slow and risky, which is the motivation for rehearsing it first in simulation and digital twins.

See also: Physical Reinvention · Integrated Platforms